2017 Nissan-Datsun Altima Technical Service Bulletin # 12-009 Date: 120203

2017 Nissan-Datsun Altima Technical Service Bulletin # 12-009 Date: 120203

Keyless Entry - Door Locks Inop. With Intelligent Key(R)

Classification: EL12-007

Reference: NTB12-009

Date: February 3, 2012

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 168

DOOR LOCK/UNLOCK INOPERATIVE WITH INTELLIGENT KEY

APPLIED VEHICLES: All 2007 and newer Nissan with Intelligent Key system

SERVICE INFORMATION:

If the doors will not lock/unlock using the Intelligent Key buttons and/or the Door Request Switch; before replacing any component:

a. Review the door look/unlock Diagnostic Items in this bulletin, and

b. Follow all diagnostic steps in the appropriate Service Manual.

NOTE:

The Intelligent Key door lock/unlock functions are controlled by several components. Proper diagnostic steps should be performed before replacing

any part. The BCM (Body Control Module) is usually not the cause of an inoperative condition.

DIAGNOSTIC ITEMS

NOTE:

When testing door lock/unlock with Intelligent Key:

^ Set the ignition switch position to OFF or LOCK.

^ Put the shift lever in Park.

^ Intelligent key is not inserted into key slot (if equipped).

^ All doors are closed.

^ Intelligent key is outside the vehicle and 6 feet or less from the request switch.

^ As needed, refer to Figure 2 above.

Check operation of the door locks with the power door lock switch.

^ If a door will lock/unlock with the power door lock switch on the inside door panel, then the actuator is OK and the wiring between the

actuator and BCM is OK.

^ If needed, refer to the appropriate Service Manual to diagnose and repair the power door lock system.

Check signals from the Intelligent Key and the vehicle antenna using Signal Tech II.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 169

^ Follow the Signal Tech II instruction manual for Intelligent Key testing.

^ The Signal Tech II instruction manual is found in ASIST under Tools & Equipment.

Correct any no-signal or low-signal conditions:

^ If there is no-signal or low-signal from the Intelligent Key, inspect the Intelligent Key and its battery.

> Refer to NTB08-107 for intelligent key inspection.

> Refer to the appropriate Service Manual for battery test procedure.

> Intelligent Key battery voltage must be above 2.8 volts.

> If the battery voltage is OK, replace the Intelligent Key.

^ If there is no-signal or low-signal from the outside door handle antenna, check the antenna.

> Refer to the appropriate Service Manual for antenna diagnostic and repair procedure.

Confirm the BCM is receiving door lock/unlock signals

^ Use C-III or C-III plus > Intelligent Key > Data Monitor.

^ REQ SW-DR/AS will change OFF > ON as Door Request Switch is pressed.

^ RKE - LOCK/UNLOCK will change OFF > ON as the buttons on the Intelligent Key (keyfob) are pressed.

NG - Repair as needed. Refer to the appropriate Service Manual

NOTE:

The Remote Keyless Entry Receiver must confirm the NATS / Intelligent Key is registered before the doors will lock/unlock with Request Switch or

the Intelligent Key (keyfob) buttons.

Confirm NATS / Intelligent Key registration

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 170

^ Refer to the appropriate Service Manual and C-III / C-III plus Operators Manual for NATS / Intelligent Key registration confirmation.

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 12-009 Date: 120203

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 12-009 Date: 120203

Keyless Entry - Door Locks Inop. With Intelligent Key(R)

Classification: EL12-007

Reference: NTB12-009

Date: February 3, 2012

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 168

DOOR LOCK/UNLOCK INOPERATIVE WITH INTELLIGENT KEY

APPLIED VEHICLES: All 2007 and newer Nissan with Intelligent Key system

SERVICE INFORMATION:

If the doors will not lock/unlock using the Intelligent Key buttons and/or the Door Request Switch; before replacing any component:

a. Review the door look/unlock Diagnostic Items in this bulletin, and

b. Follow all diagnostic steps in the appropriate Service Manual.

NOTE:

The Intelligent Key door lock/unlock functions are controlled by several components. Proper diagnostic steps should be performed before replacing

any part. The BCM (Body Control Module) is usually not the cause of an inoperative condition.

DIAGNOSTIC ITEMS

NOTE:

When testing door lock/unlock with Intelligent Key:

^ Set the ignition switch position to OFF or LOCK.

^ Put the shift lever in Park.

^ Intelligent key is not inserted into key slot (if equipped).

^ All doors are closed.

^ Intelligent key is outside the vehicle and 6 feet or less from the request switch.

^ As needed, refer to Figure 2 above.

Check operation of the door locks with the power door lock switch.

^ If a door will lock/unlock with the power door lock switch on the inside door panel, then the actuator is OK and the wiring between the

actuator and BCM is OK.

^ If needed, refer to the appropriate Service Manual to diagnose and repair the power door lock system.

Check signals from the Intelligent Key and the vehicle antenna using Signal Tech II.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 169

^ Follow the Signal Tech II instruction manual for Intelligent Key testing.

^ The Signal Tech II instruction manual is found in ASIST under Tools & Equipment.

Correct any no-signal or low-signal conditions:

^ If there is no-signal or low-signal from the Intelligent Key, inspect the Intelligent Key and its battery.

> Refer to NTB08-107 for intelligent key inspection.

> Refer to the appropriate Service Manual for battery test procedure.

> Intelligent Key battery voltage must be above 2.8 volts.

> If the battery voltage is OK, replace the Intelligent Key.

^ If there is no-signal or low-signal from the outside door handle antenna, check the antenna.

> Refer to the appropriate Service Manual for antenna diagnostic and repair procedure.

Confirm the BCM is receiving door lock/unlock signals

^ Use C-III or C-III plus > Intelligent Key > Data Monitor.

^ REQ SW-DR/AS will change OFF > ON as Door Request Switch is pressed.

^ RKE - LOCK/UNLOCK will change OFF > ON as the buttons on the Intelligent Key (keyfob) are pressed.

NG - Repair as needed. Refer to the appropriate Service Manual

NOTE:

The Remote Keyless Entry Receiver must confirm the NATS / Intelligent Key is registered before the doors will lock/unlock with Request Switch or

the Intelligent Key (keyfob) buttons.

Confirm NATS / Intelligent Key registration

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 170

^ Refer to the appropriate Service Manual and C-III / C-III plus Operators Manual for NATS / Intelligent Key registration confirmation.

2016 GMC Truck Acadia AWD V6-3.6L Technical Service Bulletin # 06-08-50-009G Date: 120203

2016 GMC Truck Acadia AWD V6-3.6L Technical Service Bulletin # 06-08-50-009G Date: 120203

2016 GMC Truck Acadia AWD V6-3.6L Page 70

Restraints - Passenger Presence System Information

INFORMATION

Bulletin No.: 06-08-50-009G

Date: February 03, 2012

Subject: Information on Passenger Presence Sensing System (PPS or PSS) Concerns with Custom Upholstery, Accessory Seat Heaters or Other

Comfort Enhancing Devices

Models:

2013 and Prior GM Passenger Cars and Trucks

Equipped with Passenger Presence Sensing System

Supercede:

This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 06-08-50-009F (Section 08 - Body and Accessories).

Concerns About Safety and Alterations to the Front Passenger Seat

Important

ON A GM VEHICLE EQUIPPED WITH A PASSENGER SENSING SYSTEM, USE THE SEAT COVERS AND OTHER

SEAT-RELATED EQUIPMENT AS RELEASED BY GM FOR THAT VEHICLE. DO NOT ALTER THE SEAT COVERS OR

SEAT-RELATED EQUIPMENT. ANY ALTERATIONS TO SEAT COVERS OR GM ACCESSORIES DEFEATS THE INTENDED

DESIGN OF THE SYSTEM. GM WILL NOT BE LIABLE FOR ANY PROBLEMS CAUSED BY USE OF SUCH IMPROPER SEAT

ALTERATIONS, INCLUDING ANY WARRANTY REPAIRS INCURRED.

The front passenger seat in many GM vehicles is equipped with a passenger sensing system that will turn off the right front passenger's frontal airbag

under certain conditions, such as when an infant or child seat is present. In some vehicles, the passenger sensing system will also turn off the right

front passenger's seat mounted side impact airbag. For the system to function properly, sensors are used in the seat to detect the presence of a

properly-seated occupant. The passenger sensing system may not operate properly if the original seat trim is replaced (1) by non-GM covers,

upholstery or trim, or (2) by GM covers, upholstery or trim designed for a different vehicle or (3) by GM covers, upholstery or trim that has been

altered by a trim shop, or (4) if any object, such as an aftermarket seat heater or a comfort enhancing pad or device is installed under the seat fabric

or between the occupant and the seat fabric.

Aftermarket Seat Heaters, Custom Upholstery, and Comfort Enhancing Pads or Devices

Important

ON A GM VEHICLE EQUIPPED WITH A PASSENGER SENSING SYSTEM, USE ONLY SEAT COVERS AND OTHER

SEAT-RELATED EQUIPMENT RELEASED AS GM ACCESSORIES FOR THAT VEHICLE. DO NOT USE ANY OTHER TYPE OF

SEAT COVERS OR SEAT-RELATED EQUIPMENT, OR GM ACCESSORIES RELEASED FOR OTHER VEHICLE APPLICATIONS.

GM WILL NOT BE LIABLE FOR ANY PROBLEMS CAUSED BY USE OF SUCH IMPROPER SEAT ACCESSORIES, INCLUDING

ANY WARRANTY REPAIRS MADE NECESSARY BY SUCH USE.

Many types of aftermarket accessories are available to customers, upfitting shops, and dealers. Some of these devices sit on top of, or are Velcro(R)

strapped to the seat while others such as seat heaters are installed under the seat fabric. Additionally, seat covers made of leather or other materials

may have different padding thickness installed that could prevent the Passenger Sensing System from functioning properly. Never alter the vehicle

seats. Never add pads or other devices to the seat cushion, as this may interfere with the operation of the Passenger Sensing System and either

prevent proper deployment of the passenger airbag or prevent proper suppression of the passenger air bag.

2014 Nissan-Datsun Altima Diagrams. DTC # 12-009 Date: 120203

2014 Nissan-Datsun Altima Diagrams. DTC # 12-009 Date: 120203

Keyless Entry - Door Locks Inop. With Intelligent Key(R)

Classification: EL12-007

Reference: NTB12-009

Date: February 3, 2012

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 168

DOOR LOCK/UNLOCK INOPERATIVE WITH INTELLIGENT KEY

APPLIED VEHICLES: All 2007 and newer Nissan with Intelligent Key system

SERVICE INFORMATION:

If the doors will not lock/unlock using the Intelligent Key buttons and/or the Door Request Switch; before replacing any component:

a. Review the door look/unlock Diagnostic Items in this bulletin, and

b. Follow all diagnostic steps in the appropriate Service Manual.

NOTE:

The Intelligent Key door lock/unlock functions are controlled by several components. Proper diagnostic steps should be performed before replacing

any part. The BCM (Body Control Module) is usually not the cause of an inoperative condition.

DIAGNOSTIC ITEMS

NOTE:

When testing door lock/unlock with Intelligent Key:

^ Set the ignition switch position to OFF or LOCK.

^ Put the shift lever in Park.

^ Intelligent key is not inserted into key slot (if equipped).

^ All doors are closed.

^ Intelligent key is outside the vehicle and 6 feet or less from the request switch.

^ As needed, refer to Figure 2 above.

Check operation of the door locks with the power door lock switch.

^ If a door will lock/unlock with the power door lock switch on the inside door panel, then the actuator is OK and the wiring between the

actuator and BCM is OK.

^ If needed, refer to the appropriate Service Manual to diagnose and repair the power door lock system.

Check signals from the Intelligent Key and the vehicle antenna using Signal Tech II.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 169

^ Follow the Signal Tech II instruction manual for Intelligent Key testing.

^ The Signal Tech II instruction manual is found in ASIST under Tools & Equipment.

Correct any no-signal or low-signal conditions:

^ If there is no-signal or low-signal from the Intelligent Key, inspect the Intelligent Key and its battery.

> Refer to NTB08-107 for intelligent key inspection.

> Refer to the appropriate Service Manual for battery test procedure.

> Intelligent Key battery voltage must be above 2.8 volts.

> If the battery voltage is OK, replace the Intelligent Key.

^ If there is no-signal or low-signal from the outside door handle antenna, check the antenna.

> Refer to the appropriate Service Manual for antenna diagnostic and repair procedure.

Confirm the BCM is receiving door lock/unlock signals

^ Use C-III or C-III plus > Intelligent Key > Data Monitor.

^ REQ SW-DR/AS will change OFF > ON as Door Request Switch is pressed.

^ RKE - LOCK/UNLOCK will change OFF > ON as the buttons on the Intelligent Key (keyfob) are pressed.

NG - Repair as needed. Refer to the appropriate Service Manual

NOTE:

The Remote Keyless Entry Receiver must confirm the NATS / Intelligent Key is registered before the doors will lock/unlock with Request Switch or

the Intelligent Key (keyfob) buttons.

Confirm NATS / Intelligent Key registration

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 170

^ Refer to the appropriate Service Manual and C-III / C-III plus Operators Manual for NATS / Intelligent Key registration confirmation.